Monacor VAM-3 Manuel d'instructions télécharger pdf (Page 10)

bright light: The battery is sufficiently recharged.

With a fully recharged battery, the

operating time is approx. 1

/2 hours.

flashing: The battery must be recharged (see

following chapter 4.1.1), however,

operation is still possible for approx.

another 10 minutes.

dim light: The battery is discharged and the

monitor is switched off.

Further operation is possible with a

separate power supply unit (see

chapter 4.2).

3) For reception, set the switch “AV” (17) to position

“out” and use the rotary switch “channel” (15) to

adjust the channel on which the transmitter or the

wireless camera operates:

position channel

0, 1 1

6…9 automatic selection between

channels 1 + 5

A automatic selection between

channels 1, 3 + 5

B…F 1

4) If the automatic selection between different chan-

nels has been activated, adjust the dwell time be-

tween one and six seconds with the control “time”

(13).

5) If the surveillance camera and the corresponding

transmitter operate correctly, the monitor displays

a picture. For basic adjustment, turn the control

“Videolevel” (5) to mid-position first. With the con-

trols “brightness” (10), “contrast” (16), and “color”

(19), adjust an optimum picture reproduction. If the

control “contrast” has been turned turned fully to

the left or to the right, readjust the basic contrast

adjustment with the control “Videolevel (5)”.

6) If the picture on the monitor is to be mirrored hori-

zontally (laterally inverted display), set the switch

“horizontal” (9) to the upper position. For vertical

reflection (picture is turned upside down), set the

switch “vertical” (8) to the upper position. With

these functions, e. g. it is possible to obtain a cor-

rect reproduction of a camera which is mounted

upside down.

7) After operation, switch off the monitor by turning

the control “On-Volume” counter-clockwise.

4.1.1 Recharging the internal

rechargeable battery

The rechargeable battery must only be recharged via

the charger AV-50CH from the MONACOR range as it

has been specially designed for the AV-200LCD.

To ensure a long service life of the rechargeable

battery, it should be completely discharged before it is

recharged. If it is frequently recharged too early, this

will result in a capacity loss of the rechargeable battery.

Use the discharge facility of the charger AV-50CH, if

required.

1) Switch off the monitor by turning the control “On-

Volume” (2) counter-clockwise.

2) Select the adapter with the blue ring (supplied with

the charger) and connect it to the inline jack of the

charger so that the positive sign of the adapter and

the positive sign of the inline jack face each other.

3) Connect the charger via the adapter to the jack

“charge” (18) of the monitor.

4) Connect the charger to a mains socket (230 V~/

50 Hz).

5) After connection, the charger will first start a test

cycle and then start recharging – also see the oper-

ating instructions of the charger!

4.2 Operation via a separate

12 V power supply unit

For continuous operation or in case of discharged

rechargeable battery, it is possible to operate the AV-

200LCD via a separate power supply unit (minimum

output current 600 mA), e. g. MONACOR PS-1615ST.

1) If the power supply unit can be set to different out-

put voltage values, set it to 12 V first.

2) Connect the power supply unit via a low voltage

plug 5.5/2.1 mm (outside/inside diameter) to the

jack “12-14V” (20). Observe the correct polarity in

any case: the positive pole must be at the inner

contact of the plug.

3) Connect the power supply unit to a mains socket

(230 V~/50 Hz).

4) Switch on the monitor by turning the control “On-

Volume” (2) clockwise. The red LED (3) will light up

as an indicator for operation and the 12 V oper-

ating voltage:

bright light: operating voltage sufficient

flashing: voltage below 11.5 V

dim light: voltage below 10.7 V,

the monitor is switched off

5) If a power supply unit is connected, the internal

rechargeable battery can be simultaneously re-

charged via the charger AV-50CH (see chapter

4.1.1).

6) Even with the monitor switched off, the power sup-

ply unit connected to the 230 V mains supply has a

low current consumption. If the monitor is not used

for a longer period, the power supply unit should

therefore be disconnected from the mains socket.

4.3 Connection of additional units

4.3.1 External antenna

To obtain a longer range to the transmitter or to the

wireless camera, an external antenna can be connect-

ed via the SMA jack instead of the omnidirectional

antenna (6) screwed on the unit. For this purpose,

MONACOR offers e. g. the directional antenna DX-80

with 8 dB gain or DX-180 with 18 dB gain.

blue

ENGLISH

1 2 ... 5 6 7 8 9 10 11 12 13 14 15

Commentaires sur ces manuels

Pas de commentaire

Monacor VAM-3 Manuel d'instructions Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Modulateur Monacor VAM-3